How to finally finish video before rendering? I hope that you guys understand my question. You see, whenever I save/render/export my video it has that huge black part between the moment when I would like to finish video and moment when it really ends.
So, please help me with this. I believe that it`s very common to all of you who use VS longer than I do.
Thanks a lot!
How to finally finish video before rendering?
Moderator: Ken Berry
-
canuck
- Posts: 2037
- Joined: Wed Mar 14, 2012 3:28 pm
- System_Drive: C
- 32bit or 64bit: 64 Bit
- Location: Deep River, Ontario, Canada
Re: How to finally finish video before rendering?
Sorry but I don't understand your question.
What do you mean by "that huge black part between the moment when I would like to finish video and moment when it really ends"? "Huge black part" where?
What do you mean by "that huge black part between the moment when I would like to finish video and moment when it really ends"? "Huge black part" where?
-
Ken Berry
- Site Admin
- Posts: 22481
- Joined: Fri Dec 10, 2004 9:36 pm
- System_Drive: C
- 32bit or 64bit: 64 Bit
- motherboard: Gigabyte B550M DS3H AC
- processor: AMD Ryzen 9 5900X
- ram: 32 GB DDR4
- Video Card: AMD RX 6600 XT
- Hard_Drive_Capacity: 1 TB SSD + 2 TB HDD
- Monitor/Display Make & Model: Kogan 32" 4K 3840 x 2160
- Corel programs: VS2022; PSP2023; DRAW2021; Painter 2022
- Location: Levin, New Zealand
Re: How to finally finish video before rendering?
Personally, if that happened to me, I would be looking at all the timelines to see what was down around the point that the video actually stopped playing, as opposed to where you thought it should end. The fact that it is doing this indicates to me that there is some small trace of either video, a photo, a title or music or voice in one of the overlay tracks. It need only be a frame or two which may have remained when you cut a longer file at that point. But it would be enough to make VS think that it was the real end of the project...
That being said, I have never experienced that in all my years of video editing. But I am careful, when editing and cutting files which are much longer than the other files in the project, to make sure all remaining traces have been cleaned out before trying to Share the project...
That being said, I have never experienced that in all my years of video editing. But I am careful, when editing and cutting files which are much longer than the other files in the project, to make sure all remaining traces have been cleaned out before trying to Share the project...
Ken Berry
-
lata
- Site Admin
- Posts: 14280
- Joined: Thu Jan 19, 2012 6:21 am
- System_Drive: C
- 32bit or 64bit: 64 Bit
- motherboard: ASUSTeK COMPUTER INC A88XM-A USB 3 1 Rev X 0x
- processor: 4 10 gigahertz AMD A10-7890K Radeon R7
- ram: 16 gb
- Video Card: on board
- sound_card: Realtek High Definition Audio
- Hard_Drive_Capacity: 500 SSD
- Monitor/Display Make & Model: LG W2242 [Monitor]
- Corel programs: CVSX, 19, 20, 22 PSP2023, PI, MS3D
- Location: UK
- Contact:
Re: How to finally finish video before rendering?
Hi
A agree with Ken that there may be some clip further down the timeline.
Below the preview screen are some navigation controls
Select the Project
Then select End ( the righthand facing arrow with the vertical line ) seems to have lost its tool tip.
That will take the timeline and cursor to the end of your project. What do you see.
A agree with Ken that there may be some clip further down the timeline.
Below the preview screen are some navigation controls
Select the Project
Then select End ( the righthand facing arrow with the vertical line ) seems to have lost its tool tip.
That will take the timeline and cursor to the end of your project. What do you see.