I am finding that it takes many seconds for a page to load, especially at startup. Sometimes it's normal, but most of the time too slow.
Also, other pages can be slow. Anytime I load VS, it's slow.
Slow to Load
Moderator: Ken Berry
-
pepegota
- Posts: 1004
- Joined: Thu Jun 11, 2009 5:49 pm
- System_Drive: C
- 32bit or 64bit: 64 Bit
- motherboard: ASUS TUF Z390-Plus
- processor: Intel i9 - 9900k
- ram: 64 GB
- Video Card: GTX 1660 6GB
- sound_card: On board sound
- Hard_Drive_Capacity: 2 TB
- Monitor/Display Make & Model: Ben Q, "21" LCD
- Corel programs: VS 2018, VS 2019, VS 2020
- Location: USA
Slow to Load
Last edited by pepegota on Sat Nov 17, 2018 9:23 pm, edited 1 time in total.
-
canuck
- Posts: 2037
- Joined: Wed Mar 14, 2012 3:28 pm
- System_Drive: C
- 32bit or 64bit: 64 Bit
- Location: Deep River, Ontario, Canada
Re: Slow to Load
Loading what pages? There is no information on what you are doing.
If loading is normal at times and "slow" at other times that means that something in your system is slowing down the process
If loading is normal at times and "slow" at other times that means that something in your system is slowing down the process
-
pepegota
- Posts: 1004
- Joined: Thu Jun 11, 2009 5:49 pm
- System_Drive: C
- 32bit or 64bit: 64 Bit
- motherboard: ASUS TUF Z390-Plus
- processor: Intel i9 - 9900k
- ram: 64 GB
- Video Card: GTX 1660 6GB
- sound_card: On board sound
- Hard_Drive_Capacity: 2 TB
- Monitor/Display Make & Model: Ben Q, "21" LCD
- Corel programs: VS 2018, VS 2019, VS 2020
- Location: USA
Re: Slow to Load
Start up and subject matter. No other sites exhibit this behavior. I just clicked on videostudio (upper left corner) and slowwwwwwww!!
Submit is none too quick either.
Submit is none too quick either.
-
canuck
- Posts: 2037
- Joined: Wed Mar 14, 2012 3:28 pm
- System_Drive: C
- 32bit or 64bit: 64 Bit
- Location: Deep River, Ontario, Canada
Re: Slow to Load
Yes the forum website is very slow at the moment. It has also been slow over the last couple of weeks. Like you I have no such slowdowns with other websites.
Your original post was not clear if you were referring to the Corel program or the forum website.
Your original post was not clear if you were referring to the Corel program or the forum website.
- Ken Berry
- Site Admin
- Posts: 22481
- Joined: Fri Dec 10, 2004 9:36 pm
- System_Drive: C
- 32bit or 64bit: 64 Bit
- motherboard: Gigabyte B550M DS3H AC
- processor: AMD Ryzen 9 5900X
- ram: 32 GB DDR4
- Video Card: AMD RX 6600 XT
- Hard_Drive_Capacity: 1 TB SSD + 2 TB HDD
- Monitor/Display Make & Model: Kogan 32" 4K 3840 x 2160
- Corel programs: VS2022; PSP2023; DRAW2021; Painter 2022
- Location: Levin, New Zealand
Re: Slow to Load
FWIW the Board is very slow at the moment in New Zealand too. It wasn't earlier this morning but, like with you, it's now taking ages to open a new page or post a message. Unfortunately, there's little I can do about it as the servers are in Taiwan and it's the weekend. I'll send a message asking them to look at what might be causing the slowdown, but realistically, given time zones etc and the weekend, they are not going to get it for another 24 hours or more.
And it's not always a problem with the servers. Two or three weeks ago users in Europe and IIRC North America were experiencing a very slow Board, but in Australia and here in New Zealand, the Board was as fast as it usually is. So that tended to indicate there was some other problem e.g. congestion on intercontinental cables?
And it's not always a problem with the servers. Two or three weeks ago users in Europe and IIRC North America were experiencing a very slow Board, but in Australia and here in New Zealand, the Board was as fast as it usually is. So that tended to indicate there was some other problem e.g. congestion on intercontinental cables?
Ken Berry
- Ken Berry
- Site Admin
- Posts: 22481
- Joined: Fri Dec 10, 2004 9:36 pm
- System_Drive: C
- 32bit or 64bit: 64 Bit
- motherboard: Gigabyte B550M DS3H AC
- processor: AMD Ryzen 9 5900X
- ram: 32 GB DDR4
- Video Card: AMD RX 6600 XT
- Hard_Drive_Capacity: 1 TB SSD + 2 TB HDD
- Monitor/Display Make & Model: Kogan 32" 4K 3840 x 2160
- Corel programs: VS2022; PSP2023; DRAW2021; Painter 2022
- Location: Levin, New Zealand
Re: Slow to Load
I sent the message, but don't expect anyone at the other end has read it yet. But 10 or so hours later, I find that the Board is back to reasonable speeds again...
Ken Berry
- RobertOZ
- Advisor
- Posts: 2426
- Joined: Tue Jun 26, 2012 12:50 am
- System_Drive: C
- 32bit or 64bit: 64 Bit
- motherboard: Asus Prime B550M-A WI-FI AM4 mATX
- processor: AMD Ryzen 5 3600 3 6 GHz
- ram: 16GB
- Video Card: Asus Geforce GTX 1650 GDDR6 Driver 551 23
- sound_card: Realtek High Definition Audio
- Hard_Drive_Capacity: 7 TB
- Monitor/Display Make & Model: Philips 32" IPS LED, Samsung 28" 3840x2160 UHD 4K
- Corel programs: VS2018/21/22/23 & MS 3D, MCC XL
- Location: Mornington, Vic. Australia
Re: Slow to Load
Still getting very slow load times, has been taking up to 4 minutes for the forum to load
